Kenmore Laundery Center Stackable Washer (Model 110.88752798) Wouldn't Drain or Spin Due to Failed Lid Switch
Verified Repair Report™ #0017
This Verified Repair Report™ documents a real Kenmore washer repair completed in Margate, Florida (33063). The customer reported that the washer would not drain or spin. After diagnosing the appliance, our technician identified a failed Lid Switch was Prevented Draining & Spinning. Replacing the lid switch restored normal washing, draining, and spinning operation.
- 🟢 Repair Completed Successfully
Repair Snapshot
| Brand: | Kenmore |
| Appliance: | Top Load Washer |
| Model: | 110.88752798 |
| Problem: | Washer Wouldn't Drain or Spin |
| Diagnosis: | Failed Lid Switch |
| Repair: | Installed New Lid Switch |
| Location: | Margate, Florida 33063 |
| Report #: | 0017 |
Customer Complaint
The customer reported that the washer would not drain or enter the spin cycle, preventing loads from completing properly.
Technician Inspection
The technician inspected the washer and determined the lid switch had failed.
A temporary bypass confirmed the remainder of the washer was operating correctly.
The defective lid switch was then replaced and the appliance was fully tested.
The washer successfully completed draining, spinning, and washing functions.
Diagnosis
Failed Lid Switch Assembly
Testing confirmed that the washer’s lid switch assembly had failed, preventing the control system from recognizing that the lid was safely closed.
Although the washer filled with water and agitated normally, the failed safety switch interrupted the drain and spin functions, causing the cycle to stop before completion.
No problems were found with the drive motor, transmission, drain pump, or timer. Diagnosis confirmed the lid switch assembly was the failed component requiring replacement.
Repair Performed
- Diagnosed drainage and spin failure
- Tested lid switch circuit
- Confirmed diagnosis with temporary bypass
- Replaced defective lid switch
- Tested complete wash cycle
- Verified proper operation
Failure Analysis
The lid switch is an important safety component on many top-load washing machines.
If the switch fails, the control system prevents the washer from entering the drain and spin cycles.
Fortunately, lid switch failures are generally straightforward to diagnose and are often repaired by replacing the failed switch.
Technician Assessment
Repair Complexity: 🟢 Basic Service
Diagnostic Difficulty: Low
Parts Replaced: Lid Switch
Repair Status: Completed
Repair Cost Category: $
DIY Friendly: 🟡 Sometimes
🛠 Repair Classification
🟢 Basic Service
The repair involved replacing a failed lid switch assembly that prevented the Kenmore Laundry Center from draining and spinning. Once the new switch was installed, the washer completed the drain and spin cycles normally. No additional repairs to the drive system, drain pump, or transmission were necessary.
Homeowner Tip
If your washer fills with water but refuses to spin or drain, avoid repeatedly restarting the cycle. A failed lid switch is a common cause, and continued attempts to operate the washer won’t usually resolve the issue.
Preventive Maintenance Tips
To help extend the life of your washer’s lid switch and reduce future interruptions:
✓ Close the washer lid gently instead of slamming it shut, which can damage the lid switch mechanism over time.
✓ Avoid overloading the washer, as excessive vibration and movement can place additional stress on the lid switch and cabinet.
✓ Ensure the washer is level, since an unbalanced machine can create excessive vibration during the spin cycle.
✓ Listen for changes in operation, such as the washer failing to start the spin cycle or requiring the lid to be opened and closed multiple times before operating.
✓ Inspect the lid strike periodically to make sure it is not cracked, bent, or loose, as it works together with the lid switch.
✓ Address drain or spin problems promptly, since continuing to use the washer with an intermittent lid switch can eventually lead to incomplete wash cycles and unnecessary wear on other components.
Common Symptoms
- Washer won't drain
- Washer won't spin
- Clothes remain soaking wet
- Washer fills normally
- Cycle stops before spin
- No unusual grinding noises
Machine Information
Brand: Kenmore
Appliance: Laundry Center Top Load Washing Machine
Model number: 110.88752798
Repair Status: ✔ Service Completed Successfully
Location: Margate, Florida 33063
Repair Report: #0017
Service Documentation
The following photographs were captured during the service visit to document the appliance and verify the exact model serviced.
Frequently Asked Questions
1. Why won't my Kenmore washer drain or spin?
A Kenmore washer that won’t drain or spin is often caused by a failed lid switch, clogged drain pump, worn drive components, or a drainage restriction. On this service call, testing confirmed the lid switch had failed, preventing the washer from entering the spin cycle. Replacing the defective switch restored normal operation.
2. Can a bad lid switch keep a washer from spinning?
Yes. On many top-loading Kenmore washers, the lid switch is a safety device that must detect the lid is closed before the washer will spin or drain. If the switch fails, the washer may fill and agitate normally but stop before the spin cycle begins.
3. How do I know if my washer lid switch is bad?
Common symptoms of a failed lid switch include:
- Washer fills and agitates but won’t spin
- Washer won’t drain at the end of the cycle
- No clicking sound when closing the lid
- Cycle stops unexpectedly
- Washer appears to do nothing during the spin cycle
A technician can confirm the diagnosis with electrical testing of the switch.
4. Can I bypass a washer lid switch?
While it is technically possible to bypass a lid switch for testing purposes, it is not recommended for normal operation. The lid switch is an important safety feature that prevents the washer from spinning with the lid open. Replacing the faulty switch is the safest and most reliable repair.
5. Is replacing a washer lid switch worth it or should I replace the washer?
In most cases, replacing a lid switch is a cost-effective repair. The part is relatively inexpensive compared to purchasing a new washing machine, and replacing it can restore years of reliable service if the rest of the appliance is in good condition. For older machines with multiple major problems, replacement may be the better long-term option.
Continue Exploring
Related Repair Reports:
Repair Report #0001 – Whirlpool Washer Not Spinning Motor Coupling Replacement
GE Washer Won’t Drain
Whirlpool Washer Won’t Spin
Kenmore Range Burner Switch Replacement
Bosch Microwave Dead Repair
Repair Report #0002 – Garbage Disposal Drain Obstruction Cleared
Appliance Repair Services:
Laundry Center Repair
Emergency Appliance Repair
Appliance Care Resources:
Why Your Washer Won’t Spin
Signs Your Lid Switch Is Failing
Should You Repair or Replace a Washer?
How Long Should a Washing Machine Last?
Need Appliance Repair?
If your appliance is having a similar problem, The Appliance Experts can help diagnose the issue and explain your repair options.
📞 (954) 256-1622 Call or Text★★★★★ Trusted by South Florida Homeowners.
✔ Honest Recommendations
✔ Experienced Technicians
✔ Detailed Repair Reports
Serving Broward, Miami-Dade & Palm Beach County
The Appliance Experts
Trusted appliance repair professionals serving homeowners throughout South Florida with expert repairs, genuine replacement parts, and detailed Repair Reports™.
REPAIR REPORTS
Refrigerator Repair Reports
Washer Repair Reports
Dryer Repair Reports
Dishwasher Repair Reports
Oven & Range Repair Reports
COMMON PROBLEMS
Repair Reports™ are based on actual technician service calls performed by The Appliance Experts. Individual appliance failures and repair recommendations may vary.
© 2026 The Appliance Experts. All Rights Reserved.
Privacy Policy | Terms of Service | Contact Us